GET A FREE CONSULT

How VFD bearing damage develops

From a real investigation · 53 seconds

How a VFD destroys a motor bearing

Animated explainer: VFD-induced bearing damage A variable frequency drive sends fast voltage pulses down an unshielded cable to a motor. Common-mode voltage couples onto the rotor through stray capacitance, so the shaft floats at tens of volts. The voltage builds across the bearing's lubricant film until the film breaks down and discharges, melting microscopic pits. Millions of discharges frost the race and then cut a washboard pattern called fluting, shown in a teardown photo. The investigation found no direct ground bond, long unshielded cable runs, no output filtering and no shaft grounding rings, with 21 to 34 volts measured on the shaft and fluting in four of four teardowns. The fixes are a direct ground bond, shielded VFD cable, drive output filtering, and shaft grounding rings. VFD variable frequency drive Motor cable STATOR WINDINGS ROTOR NDE BEARING DE BEARING Stray capacitancestator → rotor Discharge path: through the bearing SHAFT VOLTAGE 0 V COMMON-MODE VOLTAGE AT THE MOTOR 0 V PWM switching can make the motor neutral voltage step relative to ground. INSIDE THE DE BEARING (NOT TO SCALE) OUTER RACE → housing → ground INNER RACE ← shaft (charged) lubricant film lubricant film VOLTAGE ACROSS THE FILM film breaks Discharges: 0 THE RACE SURFACE, UNROLLED 1 · Pitting 2 · Frosting 3 · Fluting ACTUAL DRIVE-END INNER RACE FROM THE INVESTIGATION The washboard pattern across the raceway is fluting. Teardown photo, sanitized case study CS-01. Found in 4 of 4 teardowns. How a VFD destroys a motor bearing From a real investigation at a multi-line food plant 21–34 V peak-to-peak on the shaft · fluting in 4 of 4 teardowns · 6 failures in 7 weeks “Inverter duty” protects the windings. It doesn't protect the bearings. Check your drive-end bearings and measure shaft voltage before the next failure.
1

Simplified for clarity; not to scale. Figures in chapters 6 and 7 are from the sanitized case study CS-01. The animated meter in chapter 3 is illustrative.

Read the full case study

Select mitigation for the current path

Common-mode voltage is the average of the three phase voltages relative to a reference such as the DC-link midpoint or ground. In a balanced sinusoidal system their sum may be zero; a PWM inverter's switching states can produce a nonzero, changing common-mode voltage. High-frequency currents then follow the installation's capacitive and conductive return paths. Capacitive discharge, circulating bearing currents and shaft-grounding currents need not call for the same remedy.

Differential-mode voltage is measured between phases. Fast voltage edges and cable reflections can stress motor insulation. A dV/dt filter or output reactor selected for that stress is not automatically a common-mode bearing-current solution. Evaluate the actual filter design and drive/motor/cable combination. High-frequency bonding and correctly terminated shielding manage return paths; shaft grounding provides a bypass where appropriate; insulated bearings interrupt particular loops and may redirect current elsewhere. Follow OEM guidance and verify the resulting path, including driven equipment.

The investigator confirmed the reported 21–34 V shaft-voltage range was peak-to-peak, not RMS. It is an observation from the case, not a universal bearing-damage threshold. Waveform records, reference point, probe method and bandwidth, speed, load and lubricant-film conditions affect interpretation. This animation illustrates a mechanism and recommended options; it does not show verified post-remediation performance.

Primary OEM reference: ABB Technical guide No. 5: Bearing currents in modern AC drive systems, chapters on current mechanisms and prevention. Have a qualified person assess the installation before selecting mitigation.

Read the explanation

A variable frequency drive feeds an AC motor through a long cable. The motor is rated "inverter duty." Nothing looks wrong.

PWM output is a train of fast voltage steps. The switching states can produce a nonzero common-mode voltage, so the motor sees a stepped common-mode voltage.

Stray capacitance between the stator windings and the rotor couples that common-mode voltage onto the rotor. The shaft floats at tens of volts, and the easiest way out is through the bearings.

The grease film insulates, so the voltage builds until the film breaks down. The discharge melts a microscopic pit in the race. At PWM switching rates this repeats millions of times.

Pitting turns the race a dull gray (frosting). Over time the balls' rhythm cuts a washboard pattern: fluting. The grease turns black. This is the race from the investigation.

No direct ground bond from drive to motor. Unshielded runs over 100–140 ft. Little drive output filtering. Almost no shaft grounding. The failures had been written off as "just how it is here."

Choose mitigation for the measured current path with the drive and motor OEM. High-frequency bonding, correctly terminated shielding, common-mode filtering, shaft grounding and bearing insulation have different roles; they are not interchangeable. Implementation and post-mitigation readings were not verified in this case.

Turn what you have read into a useful next step.

Organize your equipment problem into a free preliminary engineering brief. No email required; you choose whether to share it for review.